By Linda Cerise. Electrical Wiring. Publised at Tuesday, January 23rd 2018, 19:10:16 PM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Annette Noele. Electrical Wiring. Publised at Saturday, January 20th 2018, 03:31:50 AM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 28th 2017, 11:08:59 AM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Severin Theodore. Electrical Wiring. Published at Monday, September 25th 2017, 11:07:46 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 21st 2017, 11:04:15 AM. The atmospheric vent is divided by the two halves of the carburetor. As a result fuel can leak in between the gasket and flow into the atmospheric vent and down into the carburetor. This also causes loss of fuel and a rich air/fuel mixture. The fuel level needs to be slightly below the bottom half of the carburetor to prevent this. Warping of the carburetor halves can also create an easier path for fuel to leak into the atmospheric vent.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, September 19th 2017, 10:22:23 AM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Linda Cerise. Electrical Wiring. Published at Sunday, September 17th 2017, 09:47:57 AM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Claudie Ulysse. Engine Wiring. Published at Sunday, September 17th 2017, 09:47:23 AM. The Emulsion Tube/Main Jet sits below the fuel bowl. This results in the emulsion tube and main jet to constantly have fuel pressure against it. The original design relies on the mating surfaces between the carburetor body and the main jet/emulsion tube to be perfect in order to provide a seal between each other. As corrosion and age set into your carburetor, this seal is often compromised. Since fuel is always being pulled down toward the main jet area, fuel will continuously leak out causing an overly rich air/fuel mixture, and loss of fuel.
By Annette Noele. Electrical Wiring. Published at Friday, September 15th 2017, 09:06:53 AM. Conductors and cables should run from terminal to terminal without any intervening joins. This refers to making a joint in the middle of a wire or cable. If it is necessary for any reason then use a suitable connector or terminal block. Don’t use a twisted and soldered joint.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.