By Severin Theodore. Electrical Wiring. Publised at Wednesday, January 24th 2018, 17:28:44 PM. Wires and cables (conductors) are insulated and protected by a variety of materials (insulators) each one having its own particular properties. The type of material used will be determined by the designer who will take into account the environment in which a control panel or installation is expected to operate as well as the application of individual wires within the panel.
By Augustine Yvonne. Electrical Wiring. Publised at Tuesday, January 23rd 2018, 05:36:13 AM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Severin Theodore. Electrical Wiring. Publised at Saturday, February 10th 2018, 22:56:56 PM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Linda Cerise. Engine Wiring. Published at Sunday, February 04th 2018, 13:26:33 PM. Measuring resistance can indicate the health of a component. For example we can determine if an ignition coil is healthy or not by measuring the resistance of its windings. To measure resistance, set your meter to Ω ohms resistance. If you need to select a range, select the smallest range normally 200 ohms. Place the red probe onto one of the small terminals of the ignition coil, and the black one on the remaining small terminal. Your resistance will then display. A normal ignition coil should read about 3.5 to 4 ohms. If your meter reads a much higher resistance it means your ignition coil may have a short and is faulty.
By Blandine Honorine. Electrical Wiring. Published at Sunday, February 04th 2018, 10:00:28 AM. The combined cross-sectional area of all conductors and cables is not permitted to exceed 50% of the interior cross-sectional area of the raceway. The fill provisions are based on the actual dimensions of the conductors or cables used.
By Charline Rodrigue. Engine Wiring. Published at Sunday, February 04th 2018, 05:47:20 AM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
By Linda Cerise. Electrical Wiring. Published at Sunday, February 04th 2018, 05:41:41 AM. A receptacle outlet is one in which one or more receptacles are installed for the purpose of attaching “plug and cord-connected” type devices, and a lighting outlet is one intended for a direct-wired connection to a lamp holder, luminaire (lighting fixture) or ceiling fan.
By Augustine Yvonne. Electrical Wiring. Published at Sunday, February 04th 2018, 05:27:01 AM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
By Augustine Yvonne. Electrical Wiring. Published at Sunday, February 04th 2018, 04:17:30 AM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Linda Cerise. Engine Wiring. Published at Sunday, February 04th 2018, 01:31:53 AM. Valve lapping compound is an abrasive paste that slightly wears both the valve face and seat together. I want to emphasize that the wear is very slight, and cannot replace an actual valve seat cutter. I use valve lapping compound to show me the contact points from the valve seat onto the valve face.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.