By Charline Rodrigue. Electrical Wiring. Publised at Wednesday, January 17th 2018, 01:16:54 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Blandine Honorine. Electrical Wiring. Publised at Friday, January 19th 2018, 04:11:12 AM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Augustine Yvonne. Electrical Wiring. Publised at Tuesday, January 30th 2018, 20:51:47 PM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
By Sylviane Marcelline. Engine Wiring. Published at Friday, February 09th 2018, 19:53:33 PM. To measure voltage on a battery for example you first turn your meter to DC Voltage. Place the red probe on the positive terminal of the battery and place the black probe on the negative side of the battery or on a common ground. Your voltage will display on the screen.
By Claudie Ulysse. Electrical Wiring. Published at Friday, February 09th 2018, 10:20:32 AM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Severin Theodore. Engine Wiring. Published at Friday, February 09th 2018, 04:41:46 AM. In our example below the bad spark plug ignition cable has a resistance reading of 5 mega ohms. That's 5,000,000 ohms! We know that a typical small engine ignition coil uses between 3 to 5 amps. By using the above mathematical formula we can determine that the bad spark plug ignition cable caused between 15,000,000 to 20,000,000 volts to be generated by the ignition coil!
By Blandine Honorine. Engine Wiring. Published at Thursday, February 08th 2018, 09:52:01 AM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
By Blandine Honorine. Engine Wiring. Published at Thursday, February 08th 2018, 05:25:12 AM. Let’s say you attempt to start your tractor and your starter does not engage. No click of the solenoid, nothing happens at all. Before assuming your starter is bad, grab your DMM and set it to DC Volts. Remove the wire going to the small terminal of your starter solenoid and connect the red probe of your DMM to the wire. Now connect your black probe to a ground. Turn your tractor’s key. Your DMM reads no voltage. This tells you that power is not going from your battery to the solenoid. Next remove the wires from the back of your ignition switch that are connected to the “B” and “S” terminals on your switch. Set your DMM to Continuity and connect your probes to the “B” and “S” terminals of the switch. Turn your tractor’s key and if there is no “beep” you know your ignition switch has a short internally and should be replaced.
By Blandine Honorine. Engine Wiring. Published at Wednesday, February 07th 2018, 23:14:39 PM. The air-cooled design and splash oil system works, and it keeps it simple. Less parts means easier to rebuild and keep running for another 50 years. The Cast Iron Block, combined with a great bearing system, cooling, and lubrication system makes the Kohler K Series Engine a great engine.
By Charline Rodrigue. Electrical Wiring. Published at Wednesday, February 07th 2018, 19:26:48 PM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.