By Linda Cerise. Electrical Wiring. Publised at Monday, December 25th 2017, 04:30:59 AM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Linda Cerise. Electrical Wiring. Publised at Thursday, October 05th 2017, 13:46:47 PM. A conductor is a material which will allow an electric current to flow easily. In the case of a wire connection, it needs to be a very good conductor. Good conductors include most metals. The most common conductor used in wire is copper, although you may come across others such as aluminium. An insulator on the other hand is a material which does not allow an electric current to flow. Rubber and most plastics are insulators.
By Annette Noele. Engine Wiring. Published at Tuesday, January 16th 2018, 20:20:08 PM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Blandine Honorine. Engine Wiring. Published at Tuesday, January 16th 2018, 20:05:08 PM. The atmospheric vent is divided by the two halves of the carburetor. As a result fuel can leak in between the gasket and flow into the atmospheric vent and down into the carburetor. This also causes loss of fuel and a rich air/fuel mixture. The fuel level needs to be slightly below the bottom half of the carburetor to prevent this. Warping of the carburetor halves can also create an easier path for fuel to leak into the atmospheric vent.
By Annette Noele. Electrical Wiring. Published at Tuesday, January 16th 2018, 19:03:51 PM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Claudie Ulysse. Engine Wiring. Published at Tuesday, January 16th 2018, 17:12:27 PM. To measure AC voltage for example on your engine’s stator, you first locate the two wires coming from the stator. Turn your DMM to AC Voltage. Place the red probe onto one of the wires, and the black probe on the other wire. You should read about 24 to 30 VAC.
By Babette Benjamine. Electrical Wiring. Published at Tuesday, January 16th 2018, 16:16:38 PM. Wires and cables (conductors) are insulated and protected by a variety of materials (insulators) each one having its own particular properties. The type of material used will be determined by the designer who will take into account the environment in which a control panel or installation is expected to operate as well as the application of individual wires within the panel.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 16th 2018, 15:24:21 PM. Wiring diagrams show the connections to the controller. Wiring diagrams, sometimes called “main” or “construction” diagrams, show the actual connection points for the wires to the components and terminals of the controller.
By Linda Cerise. Engine Wiring. Published at Tuesday, January 16th 2018, 09:54:39 AM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.