By Annette Noele. Electrical Wiring. Publised at Saturday, September 09th 2017, 08:05:01 AM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Linda Cerise. Electrical Wiring. Published at Thursday, October 05th 2017, 13:46:47 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Charline Rodrigue. Engine Wiring. Published at Tuesday, October 03rd 2017, 12:11:56 PM. The Neway Valve Seat Cutters I use are a manual cutting tool. It only requires finger pressure to make the cut. These cutters hold carbide cutters at perfect angles for cutting your valve seats. Depending on your engine you may need to cut your valve seats with a 46 degree or 31 degree cutter. There is a 1 degree interference angle to allow your valves to wear into the seats to form perfect seals. The valve seat cutters require a perfect valve guide in order to accurately cut the seat.
By Severin Theodore. Electrical Wiring. Published at Sunday, October 01st 2017, 11:35:11 AM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 28th 2017, 11:08:59 AM. The ability to detect, observe, and measure electricity is crucial when trying to understand how a tractor works and learning what you can do to fix it. The digital multi-meter is like a doctor’s stethoscope. It allows us to see the invisible force of electricity and measure how it interacts with the components in our engines and tractors. A digital multi-meter measures current (amps), voltage (volts), and resistance (ohms).
By Severin Theodore. Electrical Wiring. Published at Monday, September 25th 2017, 11:07:46 AM. This section requires you to support conductors in panels to keep them in place. You're permitted to use wiring channels if they're made of a flame-retardant insulating material. If you're working with back-connected control panels, you must provide access doors or swing out panels that swing about a vertical axis. Multiple-device control panels must have terminal blocks or attachment plugs and receptacles to terminate and connect all outgoing control conductors.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 21st 2017, 11:04:15 AM. Most of the circuits in lawn and garden tractors use low amperage with the exception of the starting circuit. The wiring also only runs a short distance. I recommend using 6 AWG wire for the high amp starting circuit, and the negative side of the battery to common ground connection. All other wires can be 16 or 14 AWG. The easiest and most effective way to make all of the connections is by using nylon wire crimp connectors. Nylon wire crimp connectors are more durable than ones made from PVC. They are also easier to install than soldered connections. The most common crimp connectors you will use are spade and ring connectors.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, September 19th 2017, 10:22:23 AM. Soldered connections should be made only to terminals suitable for that purpose. Transformers may be fitted with turret tags suitable for soldering and printed circuit board assemblies may have solder pins.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.