By Linda Cerise. Engine Wiring. Publised at Sunday, October 22nd 2017, 15:27:26 PM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 07:21:08 AM. The terminations of shielded or screened conductors should be terminated so that the screen cannot fray. If the screen is to be connected then make it off in the same way as for coaxial cable with a soldered pigtail and a sleeve.
By Linda Cerise. Engine Wiring. Published at Tuesday, January 16th 2018, 06:37:50 AM. When your engine is operating, your stator produces an alternating current by means of electromagnetic induction. This alternating current is fed to your rectifier/regulator by two wires. These two stator wires connect to the AC – and AC + terminals on the rectifier/regulator. The rectifier/regulator converts the alternating current into a direct current and is fed out of it through the terminal marked B+. This wire leads to the “rectifier or R” terminal on your ignition switch. This direct current charges your battery.
By Sylviane Marcelline. Engine Wiring. Published at Tuesday, January 16th 2018, 02:34:52 AM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 02:14:35 AM. A receptacle outlet is one in which one or more receptacles are installed for the purpose of attaching “plug and cord-connected” type devices, and a lighting outlet is one intended for a direct-wired connection to a lamp holder, luminaire (lighting fixture) or ceiling fan.
By Augustine Yvonne. Engine Wiring. Published at Monday, January 15th 2018, 22:58:26 PM. As your engine turns, the camshaft pushes your breaker points open, which creates a high voltage induction in your ignition coil. This high voltage power runs through your spark plug igniting your engine. Residual electricity in your ignition coil’s primary circuit is absorbed by the condenser.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, January 15th 2018, 17:39:06 PM. Conductors and cables should run from terminal to terminal without any intervening joins. This refers to making a joint in the middle of a wire or cable. If it is necessary for any reason then use a suitable connector or terminal block. Don’t use a twisted and soldered joint.
By Charline Rodrigue. Electrical Wiring. Published at Monday, January 15th 2018, 16:20:30 PM. The combined cross-sectional area of all conductors and cables is not permitted to exceed 50% of the interior cross-sectional area of the raceway. The fill provisions are based on the actual dimensions of the conductors or cables used.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.