By Severin Theodore. Engine Wiring. Publised at Thursday, January 25th 2018, 15:01:23 PM. Insert the valve cutter pilot into the valve guide, and gently place the appropriate valve cutter into the pilot. Using the “T” handle apply gentle finger pressure downwards while rotating the tool. This is all it takes to cut into the valve seats. Do this for a few revolutions. Finish, by turning the “T” handle a few times without applying finger pressure. When done correctly you should see that you have cut a uniform area around your valve seat. Repeat this process with your other valve seat.
By Annette Noele. Engine Wiring. Publised at Saturday, February 10th 2018, 22:21:43 PM. To solve the leak into the atmospheric vent make sure your float level is adjusted perfectly. The float should be perfectly parallel to the upper carburetor body or sit slightly lower than level. This keeps fuel below where the two halves of the atmospheric vent meet. Also make sure your carburetor halves are not warped when the bolts are tightened down. If there is a visible gap between the two halves of the carburetor at the atmospheric vent; sand down the two halves until the gap is gone.
By Severin Theodore. Engine Wiring. Publised at Sunday, January 28th 2018, 06:59:43 AM. The atmospheric vent is divided by the two halves of the carburetor. As a result fuel can leak in between the gasket and flow into the atmospheric vent and down into the carburetor. This also causes loss of fuel and a rich air/fuel mixture. The fuel level needs to be slightly below the bottom half of the carburetor to prevent this. Warping of the carburetor halves can also create an easier path for fuel to leak into the atmospheric vent.
By Blandine Honorine. Electrical Wiring. Published at Thursday, February 15th 2018, 15:33:27 PM. When constructing junction boxes and pull boxes, you must be careful to exclude materials such as dust, flyings, oil and coolant. After you complete all wiring operations, you must seal all unused knockouts or openings.
By Augustine Yvonne. Electrical Wiring. Published at Thursday, February 15th 2018, 15:32:49 PM. After successful completion, the troubleshooter can improve their understanding of DC, AC, three phase circuits, Relays, Contactors, PLC, Electronics, and other related technology.
By Sylviane Marcelline. Electrical Wiring. Published at Thursday, February 15th 2018, 14:13:11 PM. You are required to run conductors and cables from terminal to terminal without splices. However, an exception allows you to install a splice in leads attached to electrical equipment, such as motors and solenoids.
By Annette Noele. Engine Wiring. Published at Thursday, February 15th 2018, 07:01:16 AM. You can determine the amount of current being used and charged on your tractor’s system by placing the meter in-series with the circuits of the tractor. To do this: first remove your red probe and plug it into the 10 amp Max port on your DMM. Then set your DMM to DC Current with the range of 10 amps. Now you unplug the wire going to your ignition switch’s “B” terminal. By clipping alligator clips to your DMM probes you can now connect one probe to the “B” terminal of your ignition switch, and your other DMM probe to the wire that normally goes to “B” terminal on the ignition switch. Now when you run your tractor the current will flow through the meter and your DMM can give you a reading. It will tell you how many amps are flowing through your system.
By Claudie Ulysse. Engine Wiring. Published at Sunday, February 11th 2018, 18:11:29 PM. Measuring resistance can indicate the health of a component. For example we can determine if an ignition coil is healthy or not by measuring the resistance of its windings. To measure resistance, set your meter to Ω ohms resistance. If you need to select a range, select the smallest range normally 200 ohms. Place the red probe onto one of the small terminals of the ignition coil, and the black one on the remaining small terminal. Your resistance will then display. A normal ignition coil should read about 3.5 to 4 ohms. If your meter reads a much higher resistance it means your ignition coil may have a short and is faulty.
By Augustine Yvonne. Electrical Wiring. Published at Sunday, February 11th 2018, 17:06:58 PM. Every type of machine has unique requirements when it comes to operator safety. From an electrical standpoint, industrial machine equipment and tools - from drill presses to multi-motored automatic machines.
By Linda Cerise. Engine Wiring. Published at Sunday, February 11th 2018, 13:58:59 PM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.