By Linda Cerise. Electrical Wiring. Publised at Sunday, September 17th 2017, 09:47:57 AM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Claudie Ulysse. Electrical Wiring. Publised at Saturday, January 27th 2018, 10:46:17 AM. When electricity was originally used for practical purposes, it was used for communication in the form of the electric telegraph and the telephone. Petroleum and paraffin lamps were still lighting homes until the late 1800s, when Thomas Edison developed the light bulb.
By Claudie Ulysse. Engine Wiring. Published at Tuesday, January 23rd 2018, 09:40:54 AM. When something is wired “in parallel” it means it is wired alongside a circuit with its own positive wire. Now that we have a basic idea of electrical theory, let’s examine how it is all wired together. The example below illustrates wiring for an engine that uses battery ignition and a stator charging system.
By Sylviane Marcelline. Engine Wiring. Published at Tuesday, January 23rd 2018, 09:10:46 AM. When your engine is operating, your stator produces an alternating current by means of electromagnetic induction. This alternating current is fed to your rectifier/regulator by two wires. These two stator wires connect to the AC – and AC + terminals on the rectifier/regulator. The rectifier/regulator converts the alternating current into a direct current and is fed out of it through the terminal marked B+. This wire leads to the “rectifier or R” terminal on your ignition switch. This direct current charges your battery.
By Annette Noele. Electrical Wiring. Published at Tuesday, January 23rd 2018, 08:33:10 AM. The combined cross-sectional area of all conductors and cables is not permitted to exceed 50% of the interior cross-sectional area of the raceway. The fill provisions are based on the actual dimensions of the conductors or cables used.
By Blandine Honorine. Engine Wiring. Published at Tuesday, January 23rd 2018, 07:31:33 AM. The starter solenoid is a relay switch that contains 2 circuits and has 3 or 4 wires connecting to and from it. Two of these wires are heavy gauge, and the remaining are smaller gauge. The two heavy gauge wires are connected to your starter and to your battery. The remaining small gauge wires are connected to the small terminals on the starter solenoid and lead to the ignition switch and to the common ground. If your starter solenoid only has one small wire or terminal, the ground is through the solenoid’s mounting bracket.
By Sylviane Marcelline. Electrical Wiring. Published at Tuesday, January 23rd 2018, 06:32:48 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 23rd 2018, 05:36:13 AM. The terminations of shielded or screened conductors should be terminated so that the screen cannot fray. If the screen is to be connected then make it off in the same way as for coaxial cable with a soldered pigtail and a sleeve.
By Linda Cerise. Electrical Wiring. Published at Tuesday, January 23rd 2018, 05:16:19 AM. You are required to run conductors and cables from terminal to terminal without splices. However, an exception allows you to install a splice in leads attached to electrical equipment, such as motors and solenoids.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.