By Claudie Ulysse. Electrical Wiring. Publised at Saturday, January 27th 2018, 10:46:17 AM. A conductor is a material which will allow an electric current to flow easily. In the case of a wire connection, it needs to be a very good conductor. Good conductors include most metals. The most common conductor used in wire is copper, although you may come across others such as aluminium. An insulator on the other hand is a material which does not allow an electric current to flow. Rubber and most plastics are insulators.
By Linda Cerise. Electrical Wiring. Publised at Sunday, September 17th 2017, 09:47:57 AM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Blandine Honorine. Engine Wiring. Published at Tuesday, November 14th 2017, 18:15:48 PM. The Neway Valve Seat Cutters I use are a manual cutting tool. It only requires finger pressure to make the cut. These cutters hold carbide cutters at perfect angles for cutting your valve seats. Depending on your engine you may need to cut your valve seats with a 46 degree or 31 degree cutter. There is a 1 degree interference angle to allow your valves to wear into the seats to form perfect seals. The valve seat cutters require a perfect valve guide in order to accurately cut the seat.
By Babette Benjamine. Electrical Wiring. Published at Thursday, November 09th 2017, 17:27:42 PM. Both line and wiring diagrams are a language of pictures. It is not difficult to learn the basic symbols. Once you do, you are able to read diagrams quickly, and can often understand a circuit at a glance. The more you work with both line and wiring diagrams, the better you will become in analyzing them.
By Blandine Honorine. Engine Wiring. Published at Sunday, November 05th 2017, 17:03:19 PM. When your engine is operating, your stator produces an alternating current by means of electromagnetic induction. This alternating current is fed to your rectifier/regulator by two wires. These two stator wires connect to the AC – and AC + terminals on the rectifier/regulator. The rectifier/regulator converts the alternating current into a direct current and is fed out of it through the terminal marked B+. This wire leads to the “rectifier or R” terminal on your ignition switch. This direct current charges your battery.
By Linda Cerise. Engine Wiring. Published at Sunday, October 22nd 2017, 15:27:26 PM. When your engine is operating, your stator produces an alternating current by means of electromagnetic induction. This alternating current is fed to your rectifier/regulator by two wires. These two stator wires connect to the AC – and AC + terminals on the rectifier/regulator. The rectifier/regulator converts the alternating current into a direct current and is fed out of it through the terminal marked B+. This wire leads to the “rectifier or R” terminal on your ignition switch. This direct current charges your battery.
By Augustine Yvonne. Electrical Wiring. Published at Wednesday, October 18th 2017, 14:48:20 PM. Conductors and cables should run from terminal to terminal without any intervening joins. This refers to making a joint in the middle of a wire or cable. If it is necessary for any reason then use a suitable connector or terminal block. Don’t use a twisted and soldered joint.
By Claudie Ulysse. Engine Wiring. Published at Saturday, October 14th 2017, 14:15:58 PM. When checking these subsystems keep an eye out for evidence suggesting trouble such as sludge or debris in fuel, missing or damaged air cleaner, score marks on top of piston and cylinder walls, and excessive carbon build up on the intake and exhaust valves. All of these give you valuable insight to your problem.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, October 09th 2017, 14:02:09 PM. You must totally enclose conductors and their connection external to the control panel enclosure in suitable raceways or enclosures. Unless used for flexible connections involving small or infrequent movements, or connections to normally stationary motors, limit switches and other externally mounted devices, fittings used with raceways or multiconductor cables must be liquidtight.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.