By Claudie Ulysse. Electrical Wiring. Publised at Saturday, January 27th 2018, 10:46:17 AM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
By Linda Cerise. Electrical Wiring. Publised at Sunday, September 17th 2017, 09:47:57 AM. This section requires you to support conductors in panels to keep them in place. You're permitted to use wiring channels if they're made of a flame-retardant insulating material. If you're working with back-connected control panels, you must provide access doors or swing out panels that swing about a vertical axis. Multiple-device control panels must have terminal blocks or attachment plugs and receptacles to terminate and connect all outgoing control conductors.
By Claudie Ulysse. Electrical Wiring. Published at Friday, February 09th 2018, 10:20:32 AM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
By Severin Theodore. Engine Wiring. Published at Friday, February 09th 2018, 04:41:46 AM. You can determine the amount of current being used and charged on your tractor’s system by placing the meter in-series with the circuits of the tractor. To do this: first remove your red probe and plug it into the 10 amp Max port on your DMM. Then set your DMM to DC Current with the range of 10 amps. Now you unplug the wire going to your ignition switch’s “B” terminal. By clipping alligator clips to your DMM probes you can now connect one probe to the “B” terminal of your ignition switch, and your other DMM probe to the wire that normally goes to “B” terminal on the ignition switch. Now when you run your tractor the current will flow through the meter and your DMM can give you a reading. It will tell you how many amps are flowing through your system.
By Blandine Honorine. Engine Wiring. Published at Thursday, February 08th 2018, 09:52:01 AM. Digital Multi-Meters come in two common varieties: Auto- Ranging, and Non Auto-Ranging. A non auto-ranging meter requires you to select a range of “sensitivity” for the given function you are using. For example if you want to measure resistance, you would need to select a range of up to 200 ohms, up to 20Kohms (20,000 ohms), 200Kohms, etc. An auto-ranging meter will automatically figure out the range and give you a measurement.
By Blandine Honorine. Engine Wiring. Published at Thursday, February 08th 2018, 05:25:12 AM. To solve the leak into the atmospheric vent make sure your float level is adjusted perfectly. The float should be perfectly parallel to the upper carburetor body or sit slightly lower than level. This keeps fuel below where the two halves of the atmospheric vent meet. Also make sure your carburetor halves are not warped when the bolts are tightened down. If there is a visible gap between the two halves of the carburetor at the atmospheric vent; sand down the two halves until the gap is gone.
By Blandine Honorine. Engine Wiring. Published at Wednesday, February 07th 2018, 23:14:39 PM. Your ignition switch is a rotary switch that when turned to one of its 3 positions connects and disconnects certain contact terminals located on its backside. In the “start” position, it connects the Battery, Ignition, Rectifier, Accessory, and Start Terminals.
By Charline Rodrigue. Electrical Wiring. Published at Wednesday, February 07th 2018, 19:26:48 PM. After successful completion, the troubleshooter can improve their understanding of DC, AC, three phase circuits, Relays, Contactors, PLC, Electronics, and other related technology.
By Annette Noele. Engine Wiring. Published at Wednesday, February 07th 2018, 08:52:57 AM. A great feature of many DMM’s is the continuity setting. The continuity function measures resistance, and if there is a complete connection the meter will give an audible beep. If there is no continuity your DMM will show “OL” on the display meaning there is an open line. You can use this to test for electrical shorts in wiring or components. I commonly use this function to quickly test for shorted ignition switches and ignition coils.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.