By Blandine Honorine. Electrical Wiring. Publised at Friday, January 19th 2018, 10:47:39 AM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Annette Noele. Engine Wiring. Publised at Thursday, February 15th 2018, 07:01:16 AM. Now just reinstall the valves and reset the valve clearances per your engine’s specifications. Now that you have replaced the valves, cut the seats, and confirmed it all makes contact with each other, your engine will start easier, produce more power, and give you less trouble as you work them.
By Sylviane Marcelline. Engine Wiring. Publised at Tuesday, January 23rd 2018, 09:10:46 AM. To measure AC voltage for example on your engine’s stator, you first locate the two wires coming from the stator. Turn your DMM to AC Voltage. Place the red probe onto one of the wires, and the black probe on the other wire. You should read about 24 to 30 VAC.
By Sylviane Marcelline. Engine Wiring. Published at Tuesday, January 16th 2018, 02:34:52 AM. Measuring voltage is one of the most common tests a tractor mechanic will conduct as he troubleshoots a system. The presence of the correct voltage will determine if a component is functioning correctly or not. A common voltage test will be of the battery. A healthy battery should read about 12.5 volts, and a battery that is being charged should measure between 13 and 14.5 volts.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 02:14:35 AM. Dashed lines are drawn between the symbols to denote which switches control specific lights or receptacles. There are quite a few symbols used to represent the devices used in home electrical wiring but some of them are very similar, so care should be used when working with them!
By Augustine Yvonne. Engine Wiring. Published at Monday, January 15th 2018, 22:58:26 PM. When your ignition switch is turned in the “start” and “run” position, the “I” or ignition terminal is energized and power flows from the battery through the primary winding of the ignition coil through the points and back to the engine ground. The primary winding of the ignition coil are the two small terminals marked + (positive) and – (negative). A small gauge wire goes from the ignition switch and connects to the + positive terminal of the ignition coil. The breaker points and condenser are both connected to the – (negative) terminal of the ignition coil. Your spark plug cable is connected to the secondary terminal which is the large wire port in the top of the ignition coil. Your spark plug is then connected to the high tension spark plug cable and screwed into your engine’s combustion chamber.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, January 15th 2018, 17:39:06 PM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Charline Rodrigue. Electrical Wiring. Published at Monday, January 15th 2018, 16:20:30 PM. A conductor is a material which will allow an electric current to flow easily. In the case of a wire connection, it needs to be a very good conductor. Good conductors include most metals. The most common conductor used in wire is copper, although you may come across others such as aluminium. An insulator on the other hand is a material which does not allow an electric current to flow. Rubber and most plastics are insulators.
By Babette Benjamine. Engine Wiring. Published at Tuesday, January 09th 2018, 20:54:52 PM. A great feature of many DMM’s is the continuity setting. The continuity function measures resistance, and if there is a complete connection the meter will give an audible beep. If there is no continuity your DMM will show “OL” on the display meaning there is an open line. You can use this to test for electrical shorts in wiring or components. I commonly use this function to quickly test for shorted ignition switches and ignition coils.
By Severin Theodore. Engine Wiring. Published at Sunday, January 07th 2018, 18:37:08 PM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.