By Annette Noele. Electrical Wiring. Publised at Thursday, January 04th 2018, 08:16:01 AM. The terminations of shielded or screened conductors should be terminated so that the screen cannot fray. If the screen is to be connected then make it off in the same way as for coaxial cable with a soldered pigtail and a sleeve.
By Annette Noele. Electrical Wiring. Publised at Thursday, January 18th 2018, 23:29:05 PM. Every type of machine has unique requirements when it comes to operator safety. From an electrical standpoint, industrial machine equipment and tools - from drill presses to multi-motored automatic machines.
By Charline Rodrigue. Engine Wiring. Publised at Wednesday, August 02nd 2017, 18:14:16 PM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Claudie Ulysse. Electrical Wiring. Published at Wednesday, January 17th 2018, 15:00:45 PM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Claudie Ulysse. Electrical Wiring. Published at Wednesday, January 17th 2018, 12:13:48 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Linda Cerise. Electrical Wiring. Published at Wednesday, January 17th 2018, 11:52:22 AM. Electricity is supplied to your home through your electric utility’s overhead or buried power lines. Before entering your home, electricity passes through a watt-hour meter which measures the amount of electricity used.
By Claudie Ulysse. Electrical Wiring. Published at Wednesday, January 17th 2018, 11:29:13 AM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Claudie Ulysse. Electrical Wiring. Published at Wednesday, January 17th 2018, 10:21:39 AM. Wiring diagrams show the connections to the controller. Wiring diagrams, sometimes called “main” or “construction” diagrams, show the actual connection points for the wires to the components and terminals of the controller.
By Annette Noele. Engine Wiring. Published at Wednesday, January 17th 2018, 08:47:52 AM. They are heavy. In most applications today their power to weight ratio is not considered impressive. But when they power 4 wheeled machines such as Lawn and Garden Tractors, Skidsteers, and Road Grading Machines, you want that weight to aid in delivering that power to the ground.
By Charline Rodrigue. Engine Wiring. Published at Wednesday, January 17th 2018, 05:34:17 AM. I love the old quote, “How do you eat an elephant? One bite at a time.” If your engine is running poorly it could be caused by several problems. It’s best to break your problem down into separate systems and work through each system individually.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.