By Augustine Yvonne. Electrical Wiring. Publised at Friday, January 26th 2018, 00:12:32 AM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
By Charline Rodrigue. Electrical Wiring. Publised at Friday, January 19th 2018, 10:34:45 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Blandine Honorine. Electrical Wiring. Published at Wednesday, January 31st 2018, 07:08:40 AM. You must totally enclose conductors and their connection external to the control panel enclosure in suitable raceways or enclosures. Unless used for flexible connections involving small or infrequent movements, or connections to normally stationary motors, limit switches and other externally mounted devices, fittings used with raceways or multiconductor cables must be liquidtight.
By Claudie Ulysse. Engine Wiring. Published at Wednesday, January 31st 2018, 03:47:38 AM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Sylviane Marcelline. Electrical Wiring. Published at Wednesday, January 31st 2018, 01:18:30 AM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 30th 2018, 20:51:47 PM. You are required to run conductors and cables from terminal to terminal without splices. However, an exception allows you to install a splice in leads attached to electrical equipment, such as motors and solenoids.
By Babette Benjamine. Engine Wiring. Published at Tuesday, January 30th 2018, 20:14:42 PM. The valve face is the area on the valve that makes contact with the valve seat. It can become worn, warped and pitted over time. In order to correct this you will need a valve face grinder. These are expensive tools, so I recommend replacing the valves with new ones when you can. The rest of this article will assume you are using brand new valves.
By Sylviane Marcelline. Engine Wiring. Published at Tuesday, January 30th 2018, 17:34:17 PM. To turn your starter, electricity flows from the battery, through the ignition switch, and to the small terminals on the starter solenoid. This electricity causes an electromagnet inside the starter solenoid to connect the two heavy gauge wires and form a complete circuit. High amperage electric flow then goes through your starter, turning your engine’s flywheel.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 30th 2018, 16:32:34 PM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.