By Sylviane Marcelline. Electrical Wiring. Publised at Monday, October 09th 2017, 14:02:09 PM. Electricity is supplied to your home through your electric utility’s overhead or buried power lines. Before entering your home, electricity passes through a watt-hour meter which measures the amount of electricity used.
By Blandine Honorine. Electrical Wiring. Published at Wednesday, January 31st 2018, 07:08:40 AM. For grounded control circuits, you may use a green (with or without one or more yellow stripes) or a bare conductor to connect the transformer terminal to a grounding terminal on the control panel.
By Claudie Ulysse. Engine Wiring. Published at Wednesday, January 31st 2018, 03:47:38 AM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
By Sylviane Marcelline. Electrical Wiring. Published at Wednesday, January 31st 2018, 01:18:30 AM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 30th 2018, 20:51:47 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Babette Benjamine. Engine Wiring. Published at Tuesday, January 30th 2018, 20:14:42 PM. Let’s say you attempt to start your tractor and your starter does not engage. No click of the solenoid, nothing happens at all. Before assuming your starter is bad, grab your DMM and set it to DC Volts. Remove the wire going to the small terminal of your starter solenoid and connect the red probe of your DMM to the wire. Now connect your black probe to a ground. Turn your tractor’s key. Your DMM reads no voltage. This tells you that power is not going from your battery to the solenoid. Next remove the wires from the back of your ignition switch that are connected to the “B” and “S” terminals on your switch. Set your DMM to Continuity and connect your probes to the “B” and “S” terminals of the switch. Turn your tractor’s key and if there is no “beep” you know your ignition switch has a short internally and should be replaced.
By Sylviane Marcelline. Engine Wiring. Published at Tuesday, January 30th 2018, 17:34:17 PM. In our example below the bad spark plug ignition cable has a resistance reading of 5 mega ohms. That's 5,000,000 ohms! We know that a typical small engine ignition coil uses between 3 to 5 amps. By using the above mathematical formula we can determine that the bad spark plug ignition cable caused between 15,000,000 to 20,000,000 volts to be generated by the ignition coil!
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 30th 2018, 16:32:34 PM. Soldered connections should be made only to terminals suitable for that purpose. Transformers may be fitted with turret tags suitable for soldering and printed circuit board assemblies may have solder pins.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.