By Augustine Yvonne. Electrical Wiring. Publised at Wednesday, August 30th 2017, 02:31:22 AM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
By Linda Cerise. Electrical Wiring. Published at Monday, December 25th 2017, 04:30:59 AM. You are required to run conductors and cables from terminal to terminal without splices. However, an exception allows you to install a splice in leads attached to electrical equipment, such as motors and solenoids.
By Blandine Honorine. Engine Wiring. Published at Sunday, December 24th 2017, 02:56:15 AM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
By Blandine Honorine. Electrical Wiring. Published at Wednesday, December 20th 2017, 00:42:29 AM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Severin Theodore. Electrical Wiring. Published at Tuesday, December 19th 2017, 23:13:04 PM. Line diagrams, also called “schematic” or “elementary” diagrams, show the circuits which form the basic operation of the controller. They do not indicate the physical relationships of the various components in the controller. They are an ideal means for troubleshooting a circuit.
By Severin Theodore. Electrical Wiring. Published at Thursday, December 14th 2017, 23:08:15 PM. Wiring diagrams show the connections to the controller. Wiring diagrams, sometimes called “main” or “construction” diagrams, show the actual connection points for the wires to the components and terminals of the controller.
By Charline Rodrigue. Electrical Wiring. Published at Sunday, December 10th 2017, 22:32:01 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Annette Noele. Engine Wiring. Published at Friday, December 08th 2017, 20:38:46 PM. In our example below the bad spark plug ignition cable has a resistance reading of 5 mega ohms. That's 5,000,000 ohms! We know that a typical small engine ignition coil uses between 3 to 5 amps. By using the above mathematical formula we can determine that the bad spark plug ignition cable caused between 15,000,000 to 20,000,000 volts to be generated by the ignition coil!
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.