By Severin Theodore. Electrical Wiring. Publised at Saturday, January 27th 2018, 01:24:41 AM. For grounded control circuits, you may use a green (with or without one or more yellow stripes) or a bare conductor to connect the transformer terminal to a grounding terminal on the control panel.
By Charline Rodrigue. Electrical Wiring. Publised at Wednesday, January 17th 2018, 01:16:54 AM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Linda Cerise. Electrical Wiring. Publised at Thursday, January 18th 2018, 06:53:45 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Sylviane Marcelline. Electrical Wiring. Published at Thursday, February 01st 2018, 06:24:23 AM. It would then be connected to the contactors and overload relays that constitute the motor starter. Two of the phases are also connected to the transformer to power the logic. The start and stop buttons are at the left of the box (note: normally these are mounted elsewhere, and a separate layout drawing would be needed).
By Annette Noele. Electrical Wiring. Published at Wednesday, January 31st 2018, 21:22:35 PM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
By Blandine Honorine. Electrical Wiring. Published at Wednesday, January 31st 2018, 07:08:40 AM. A receptacle outlet is one in which one or more receptacles are installed for the purpose of attaching “plug and cord-connected” type devices, and a lighting outlet is one intended for a direct-wired connection to a lamp holder, luminaire (lighting fixture) or ceiling fan.
By Claudie Ulysse. Engine Wiring. Published at Wednesday, January 31st 2018, 03:47:38 AM. As your engine turns, the camshaft pushes your breaker points open, which creates a high voltage induction in your ignition coil. This high voltage power runs through your spark plug igniting your engine. Residual electricity in your ignition coil’s primary circuit is absorbed by the condenser.
By Sylviane Marcelline. Electrical Wiring. Published at Wednesday, January 31st 2018, 01:18:30 AM. The diagram also shows numbering for the wires in the device. This is essential for industrial control systems that may contain hundreds or thousands of wires. These numbering schemes are often particular to each facility, but there are tools to help make wire labels that will appear in the final controls cabinet.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 30th 2018, 20:51:47 PM. Wiring diagrams show the connections to the controller. Wiring diagrams, sometimes called “main” or “construction” diagrams, show the actual connection points for the wires to the components and terminals of the controller.
By Babette Benjamine. Engine Wiring. Published at Tuesday, January 30th 2018, 20:14:42 PM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.