By Claudie Ulysse. Electrical Wiring. Publised at Saturday, January 20th 2018, 10:22:35 AM. Every type of machine has unique requirements when it comes to operator safety. From an electrical standpoint, industrial machine equipment and tools - from drill presses to multi-motored automatic machines - can present special fire and shock hazards.
By Charline Rodrigue. Electrical Wiring. Publised at Monday, August 28th 2017, 02:21:14 AM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Severin Theodore. Electrical Wiring. Publised at Sunday, October 01st 2017, 11:35:11 AM. Conductors and cables should run from terminal to terminal without any intervening joins. This refers to making a joint in the middle of a wire or cable. If it is necessary for any reason then use a suitable connector or terminal block. Don’t use a twisted and soldered joint.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 02:14:35 AM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Augustine Yvonne. Engine Wiring. Published at Monday, January 15th 2018, 22:58:26 PM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, January 15th 2018, 17:39:06 PM. Soldered connections should be made only to terminals suitable for that purpose. Transformers may be fitted with turret tags suitable for soldering and printed circuit board assemblies may have solder pins.
By Charline Rodrigue. Electrical Wiring. Published at Monday, January 15th 2018, 16:20:30 PM. Line diagrams, also called “schematic” or “elementary” diagrams, show the circuits which form the basic operation of the controller. They do not indicate the physical relationships of the various components in the controller. They are an ideal means for troubleshooting a circuit.
By Babette Benjamine. Engine Wiring. Published at Tuesday, January 09th 2018, 20:54:52 PM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
By Severin Theodore. Engine Wiring. Published at Sunday, January 07th 2018, 18:37:08 PM. When your ignition switch is turned in the “start” and “run” position, the “I” or ignition terminal is energized and power flows from the battery through the primary winding of the ignition coil through the points and back to the engine ground. The primary winding of the ignition coil are the two small terminals marked + (positive) and – (negative). A small gauge wire goes from the ignition switch and connects to the + positive terminal of the ignition coil. The breaker points and condenser are both connected to the – (negative) terminal of the ignition coil. Your spark plug cable is connected to the secondary terminal which is the large wire port in the top of the ignition coil. Your spark plug is then connected to the high tension spark plug cable and screwed into your engine’s combustion chamber.
By Blandine Honorine. Engine Wiring. Published at Friday, January 05th 2018, 10:47:51 AM. The valve seat cutters require perfect valve guides to cut accurately. Measure your valve guides and compare them to your engine’s specifications to make sure they are centered and not overly worn. If they are worn, you can either replace them or use a special cutter pilot before continuing.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.