By Charline Rodrigue. Electrical Wiring. Publised at Monday, August 28th 2017, 02:21:14 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Blandine Honorine. Electrical Wiring. Published at Monday, February 05th 2018, 11:24:22 AM. Workshops manufacturing parts in PVC or rubber use high-frequency welding processes to perform assembly. The propagation of strong magnetic fields and high-frequency waves is not easily controllable.
By Charline Rodrigue. Engine Wiring. Published at Monday, February 05th 2018, 03:16:38 AM. The starter solenoid is a relay switch that contains 2 circuits and has 3 or 4 wires connecting to and from it. Two of these wires are heavy gauge, and the remaining are smaller gauge. The two heavy gauge wires are connected to your starter and to your battery. The remaining small gauge wires are connected to the small terminals on the starter solenoid and lead to the ignition switch and to the common ground. If your starter solenoid only has one small wire or terminal, the ground is through the solenoid’s mounting bracket.
By Blandine Honorine. Engine Wiring. Published at Monday, February 05th 2018, 03:08:40 AM. The Emulsion Tube/Main Jet sits below the fuel bowl. This results in the emulsion tube and main jet to constantly have fuel pressure against it. The original design relies on the mating surfaces between the carburetor body and the main jet/emulsion tube to be perfect in order to provide a seal between each other. As corrosion and age set into your carburetor, this seal is often compromised. Since fuel is always being pulled down toward the main jet area, fuel will continuously leak out causing an overly rich air/fuel mixture, and loss of fuel.
By Severin Theodore. Electrical Wiring. Published at Sunday, February 04th 2018, 22:24:23 PM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Claudie Ulysse. Electrical Wiring. Published at Sunday, February 04th 2018, 17:54:25 PM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Augustine Yvonne. Electrical Wiring. Published at Sunday, February 04th 2018, 14:04:59 PM. When electricity was originally used for practical purposes, it was used for communication in the form of the electric telegraph and the telephone. Petroleum and paraffin lamps were still lighting homes until the late 1800s, when Thomas Edison developed the light bulb.
By Linda Cerise. Engine Wiring. Published at Sunday, February 04th 2018, 13:26:33 PM. Let’s say you attempt to start your tractor and your starter does not engage. No click of the solenoid, nothing happens at all. Before assuming your starter is bad, grab your DMM and set it to DC Volts. Remove the wire going to the small terminal of your starter solenoid and connect the red probe of your DMM to the wire. Now connect your black probe to a ground. Turn your tractor’s key. Your DMM reads no voltage. This tells you that power is not going from your battery to the solenoid. Next remove the wires from the back of your ignition switch that are connected to the “B” and “S” terminals on your switch. Set your DMM to Continuity and connect your probes to the “B” and “S” terminals of the switch. Turn your tractor’s key and if there is no “beep” you know your ignition switch has a short internally and should be replaced.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.