By Charline Rodrigue. Electrical Wiring. Publised at Monday, August 28th 2017, 02:21:14 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Severin Theodore. Electrical Wiring. Published at Friday, January 26th 2018, 16:02:16 PM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Augustine Yvonne. Electrical Wiring. Published at Friday, January 26th 2018, 00:12:32 AM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Severin Theodore. Engine Wiring. Published at Thursday, January 25th 2018, 21:08:01 PM. Measuring voltage is one of the most common tests a tractor mechanic will conduct as he troubleshoots a system. The presence of the correct voltage will determine if a component is functioning correctly or not. A common voltage test will be of the battery. A healthy battery should read about 12.5 volts, and a battery that is being charged should measure between 13 and 14.5 volts.
By Blandine Honorine. Electrical Wiring. Published at Thursday, January 25th 2018, 16:07:37 PM. You must totally enclose conductors and their connection external to the control panel enclosure in suitable raceways or enclosures. Unless used for flexible connections involving small or infrequent movements, or connections to normally stationary motors, limit switches and other externally mounted devices, fittings used with raceways or multiconductor cables must be liquidtight.
By Severin Theodore. Engine Wiring. Published at Thursday, January 25th 2018, 15:01:23 PM. Let’s say you attempt to start your tractor and your starter does not engage. No click of the solenoid, nothing happens at all. Before assuming your starter is bad, grab your DMM and set it to DC Volts. Remove the wire going to the small terminal of your starter solenoid and connect the red probe of your DMM to the wire. Now connect your black probe to a ground. Turn your tractor’s key. Your DMM reads no voltage. This tells you that power is not going from your battery to the solenoid. Next remove the wires from the back of your ignition switch that are connected to the “B” and “S” terminals on your switch. Set your DMM to Continuity and connect your probes to the “B” and “S” terminals of the switch. Turn your tractor’s key and if there is no “beep” you know your ignition switch has a short internally and should be replaced.
By Annette Noele. Electrical Wiring. Published at Thursday, January 25th 2018, 13:36:46 PM. Both line and wiring diagrams are a language of pictures. It is not difficult to learn the basic symbols. Once you do, you are able to read diagrams quickly, and can often understand a circuit at a glance. The more you work with both line and wiring diagrams, the better you will become in analyzing them.
By Annette Noele. Electrical Wiring. Published at Thursday, January 25th 2018, 10:20:38 AM. The diagram also shows numbering for the wires in the device. This is essential for industrial control systems that may contain hundreds or thousands of wires. These numbering schemes are often particular to each facility, but there are tools to help make wire labels that will appear in the final controls cabinet.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.