By Severin Theodore. Electrical Wiring. Publised at Sunday, October 01st 2017, 11:35:11 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Annette Noele. Electrical Wiring. Published at Tuesday, January 16th 2018, 19:03:51 PM. Ensure that identification tags and cable markers are legible, marked with a permanent ink and suitable for the environment where the panel is to be used. They should also correspond with those shown in the machine drawings and instruction or service documentation.
By Claudie Ulysse. Engine Wiring. Published at Tuesday, January 16th 2018, 17:12:27 PM. To measure AC voltage for example on your engine’s stator, you first locate the two wires coming from the stator. Turn your DMM to AC Voltage. Place the red probe onto one of the wires, and the black probe on the other wire. You should read about 24 to 30 VAC.
By Babette Benjamine. Electrical Wiring. Published at Tuesday, January 16th 2018, 16:16:38 PM. Every type of machine has unique requirements when it comes to operator safety. From an electrical standpoint, industrial machine equipment and tools - from drill presses to multi-motored automatic machines.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 16th 2018, 15:24:21 PM. Modern electrical machine tool equipment may vary from that of a single-motor machine (such as a drill press that performs simple, repetitive operations) to very large, multimotored automatic machines, which contain highly complex electrical control systems. Typically, these machines are especially designed, factory-wired, tested by the builder and then erected in the plant.
By Linda Cerise. Engine Wiring. Published at Tuesday, January 16th 2018, 09:54:39 AM. Digital Multi-Meters come in two common varieties: Auto- Ranging, and Non Auto-Ranging. A non auto-ranging meter requires you to select a range of “sensitivity” for the given function you are using. For example if you want to measure resistance, you would need to select a range of up to 200 ohms, up to 20Kohms (20,000 ohms), 200Kohms, etc. An auto-ranging meter will automatically figure out the range and give you a measurement.
By Severin Theodore. Engine Wiring. Published at Tuesday, January 16th 2018, 08:59:14 AM. When your ignition switch is turned in the “start” and “run” position, the “I” or ignition terminal is energized and power flows from the battery through the primary winding of the ignition coil through the points and back to the engine ground. The primary winding of the ignition coil are the two small terminals marked + (positive) and – (negative). A small gauge wire goes from the ignition switch and connects to the + positive terminal of the ignition coil. The breaker points and condenser are both connected to the – (negative) terminal of the ignition coil. Your spark plug cable is connected to the secondary terminal which is the large wire port in the top of the ignition coil. Your spark plug is then connected to the high tension spark plug cable and screwed into your engine’s combustion chamber.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 07:21:08 AM. When including a PLC in the ladder diagram still remains. But, it does tend to become more complex. Figure 5 below shows a schematic diagram for a PLC based motor control system, similar to the previous motor control example.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.