By Charline Rodrigue. Electrical Wiring. Publised at Sunday, December 10th 2017, 22:32:01 PM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Severin Theodore. Engine Wiring. Published at Sunday, January 07th 2018, 18:37:08 PM. The Emulsion Tube/Main Jet sits below the fuel bowl. This results in the emulsion tube and main jet to constantly have fuel pressure against it. The original design relies on the mating surfaces between the carburetor body and the main jet/emulsion tube to be perfect in order to provide a seal between each other. As corrosion and age set into your carburetor, this seal is often compromised. Since fuel is always being pulled down toward the main jet area, fuel will continuously leak out causing an overly rich air/fuel mixture, and loss of fuel.
By Blandine Honorine. Engine Wiring. Published at Friday, January 05th 2018, 10:47:51 AM. When your ignition switch is turned in the “start” and “run” position, the “I” or ignition terminal is energized and power flows from the battery through the primary winding of the ignition coil through the points and back to the engine ground. The primary winding of the ignition coil are the two small terminals marked + (positive) and – (negative). A small gauge wire goes from the ignition switch and connects to the + positive terminal of the ignition coil. The breaker points and condenser are both connected to the – (negative) terminal of the ignition coil. Your spark plug cable is connected to the secondary terminal which is the large wire port in the top of the ignition coil. Your spark plug is then connected to the high tension spark plug cable and screwed into your engine’s combustion chamber.
By Annette Noele. Electrical Wiring. Published at Thursday, January 04th 2018, 08:16:01 AM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 02nd 2018, 07:47:42 AM. The diagram also shows numbering for the wires in the device. This is essential for industrial control systems that may contain hundreds or thousands of wires. These numbering schemes are often particular to each facility, but there are tools to help make wire labels that will appear in the final controls cabinet.
By Claudie Ulysse. Electrical Wiring. Published at Sunday, December 31st 2017, 07:34:05 AM. The diagram also shows numbering for the wires in the device. This is essential for industrial control systems that may contain hundreds or thousands of wires. These numbering schemes are often particular to each facility, but there are tools to help make wire labels that will appear in the final controls cabinet.
By Linda Cerise. Electrical Wiring. Published at Monday, December 25th 2017, 04:30:59 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Blandine Honorine. Engine Wiring. Published at Sunday, December 24th 2017, 02:56:15 AM. A great feature of many DMM’s is the continuity setting. The continuity function measures resistance, and if there is a complete connection the meter will give an audible beep. If there is no continuity your DMM will show “OL” on the display meaning there is an open line. You can use this to test for electrical shorts in wiring or components. I commonly use this function to quickly test for shorted ignition switches and ignition coils.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.