By Charline Rodrigue. Electrical Wiring. Publised at Sunday, December 10th 2017, 22:32:01 PM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Claudie Ulysse. Electrical Wiring. Published at Friday, February 09th 2018, 10:20:32 AM. Wires and cables (conductors) are insulated and protected by a variety of materials (insulators) each one having its own particular properties. The type of material used will be determined by the designer who will take into account the environment in which a control panel or installation is expected to operate as well as the application of individual wires within the panel.
By Severin Theodore. Engine Wiring. Published at Friday, February 09th 2018, 04:41:46 AM. Valve lapping compound is an abrasive paste that slightly wears both the valve face and seat together. I want to emphasize that the wear is very slight, and cannot replace an actual valve seat cutter. I use valve lapping compound to show me the contact points from the valve seat onto the valve face.
By Blandine Honorine. Engine Wiring. Published at Thursday, February 08th 2018, 09:52:01 AM. Insert the valve cutter pilot into the valve guide, and gently place the appropriate valve cutter into the pilot. Using the “T” handle apply gentle finger pressure downwards while rotating the tool. This is all it takes to cut into the valve seats. Do this for a few revolutions. Finish, by turning the “T” handle a few times without applying finger pressure. When done correctly you should see that you have cut a uniform area around your valve seat. Repeat this process with your other valve seat.
By Blandine Honorine. Engine Wiring. Published at Thursday, February 08th 2018, 05:25:12 AM. To solve the leak into the atmospheric vent make sure your float level is adjusted perfectly. The float should be perfectly parallel to the upper carburetor body or sit slightly lower than level. This keeps fuel below where the two halves of the atmospheric vent meet. Also make sure your carburetor halves are not warped when the bolts are tightened down. If there is a visible gap between the two halves of the carburetor at the atmospheric vent; sand down the two halves until the gap is gone.
By Blandine Honorine. Engine Wiring. Published at Wednesday, February 07th 2018, 23:14:39 PM. To measure AC voltage for example on your engine’s stator, you first locate the two wires coming from the stator. Turn your DMM to AC Voltage. Place the red probe onto one of the wires, and the black probe on the other wire. You should read about 24 to 30 VAC.
By Charline Rodrigue. Electrical Wiring. Published at Wednesday, February 07th 2018, 19:26:48 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Annette Noele. Engine Wiring. Published at Wednesday, February 07th 2018, 08:52:57 AM. I love the old quote, “How do you eat an elephant? One bite at a time.” If your engine is running poorly it could be caused by several problems. It’s best to break your problem down into separate systems and work through each system individually.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.