By Babette Benjamine. Electrical Wiring. Publised at Tuesday, November 28th 2017, 18:51:48 PM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Claudie Ulysse. Electrical Wiring. Publised at Wednesday, January 24th 2018, 10:54:28 AM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Claudie Ulysse. Electrical Wiring. Publised at Friday, January 19th 2018, 20:08:48 PM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Annette Noele. Electrical Wiring. Published at Saturday, September 09th 2017, 08:05:01 AM. The dedication of panels by power class is the most efficient measure to obtain an excellent “EMC” result. Moreover, separate routing of disturbing and sensitive cables ensures minimum coupling.
By Augustine Yvonne. Electrical Wiring. Published at Thursday, September 07th 2017, 06:58:27 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Severin Theodore. Engine Wiring. Published at Tuesday, September 05th 2017, 06:02:25 AM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Augustine Yvonne. Electrical Wiring. Published at Sunday, September 03rd 2017, 06:01:46 AM. Ensure that identification tags and cable markers are legible, marked with a permanent ink and suitable for the environment where the panel is to be used. They should also correspond with those shown in the machine drawings and instruction or service documentation.
By Linda Cerise. Electrical Wiring. Published at Friday, September 01st 2017, 04:53:51 AM. Conductors and cables should run from terminal to terminal without any intervening joins. This refers to making a joint in the middle of a wire or cable. If it is necessary for any reason then use a suitable connector or terminal block. Don’t use a twisted and soldered joint.
By Augustine Yvonne. Electrical Wiring. Published at Wednesday, August 30th 2017, 02:31:22 AM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Charline Rodrigue. Electrical Wiring. Published at Monday, August 28th 2017, 02:21:14 AM. When electricity was originally used for practical purposes, it was used for communication in the form of the electric telegraph and the telephone. Petroleum and paraffin lamps were still lighting homes until the late 1800s, when Thomas Edison developed the light bulb.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.