By Annette Noele. Electrical Wiring. Publised at Tuesday, January 23rd 2018, 08:33:10 AM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
By Linda Cerise. Electrical Wiring. Publised at Sunday, February 04th 2018, 05:41:41 AM. Line diagrams, also called “schematic” or “elementary” diagrams, show the circuits which form the basic operation of the controller. They do not indicate the physical relationships of the various components in the controller. They are an ideal means for troubleshooting a circuit.
By Charline Rodrigue. Engine Wiring. Published at Sunday, January 21st 2018, 06:08:32 AM. A great feature of many DMM’s is the continuity setting. The continuity function measures resistance, and if there is a complete connection the meter will give an audible beep. If there is no continuity your DMM will show “OL” on the display meaning there is an open line. You can use this to test for electrical shorts in wiring or components. I commonly use this function to quickly test for shorted ignition switches and ignition coils.
By Claudie Ulysse. Engine Wiring. Published at Sunday, January 21st 2018, 02:18:55 AM. The starter solenoid is a relay switch that contains 2 circuits and has 3 or 4 wires connecting to and from it. Two of these wires are heavy gauge, and the remaining are smaller gauge. The two heavy gauge wires are connected to your starter and to your battery. The remaining small gauge wires are connected to the small terminals on the starter solenoid and lead to the ignition switch and to the common ground. If your starter solenoid only has one small wire or terminal, the ground is through the solenoid’s mounting bracket.
By Blandine Honorine. Electrical Wiring. Published at Sunday, January 21st 2018, 01:42:33 AM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Babette Benjamine. Engine Wiring. Published at Sunday, January 21st 2018, 01:03:18 AM. As the piston in your engine moves downward it creates a vacuum which draws in air through the intake end of the carburetor. As the air travels through the venturi, the air’s pressure drops, and fuel is drawn down from the fuel bowl, and then back up through the main jet and emulsion tube. The low pressure air mixes with and atomizes the fuel. This air/fuel mixture continues through the intake valve and into your combustion chamber.
By Charline Rodrigue. Electrical Wiring. Published at Saturday, January 20th 2018, 23:55:13 PM. Dashed lines are drawn between the symbols to denote which switches control specific lights or receptacles. There are quite a few symbols used to represent the devices used in home electrical wiring but some of them are very similar, so care should be used when working with them!
By Claudie Ulysse. Engine Wiring. Published at Saturday, January 20th 2018, 22:59:05 PM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Charline Rodrigue. Electrical Wiring. Published at Saturday, January 20th 2018, 19:16:24 PM. It would then be connected to the contactors and overload relays that constitute the motor starter. Two of the phases are also connected to the transformer to power the logic. The start and stop buttons are at the left of the box (note: normally these are mounted elsewhere, and a separate layout drawing would be needed).
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.