By Severin Theodore. Electrical Wiring. Publised at Thursday, January 25th 2018, 10:12:47 AM. A conductor is a material which will allow an electric current to flow easily. In the case of a wire connection, it needs to be a very good conductor. Good conductors include most metals. The most common conductor used in wire is copper, although you may come across others such as aluminium. An insulator on the other hand is a material which does not allow an electric current to flow. Rubber and most plastics are insulators.
By Annette Noele. Electrical Wiring. Publised at Sunday, January 28th 2018, 18:50:48 PM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Claudie Ulysse. Electrical Wiring. Publised at Tuesday, January 30th 2018, 12:02:29 PM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Annette Noele. Electrical Wiring. Published at Tuesday, January 16th 2018, 19:03:51 PM. The combined cross-sectional area of all conductors and cables is not permitted to exceed 50% of the interior cross-sectional area of the raceway. The fill provisions are based on the actual dimensions of the conductors or cables used.
By Claudie Ulysse. Engine Wiring. Published at Tuesday, January 16th 2018, 17:12:27 PM. Now just reinstall the valves and reset the valve clearances per your engine’s specifications. Now that you have replaced the valves, cut the seats, and confirmed it all makes contact with each other, your engine will start easier, produce more power, and give you less trouble as you work them.
By Babette Benjamine. Electrical Wiring. Published at Tuesday, January 16th 2018, 16:16:38 PM. The terminations of shielded or screened conductors should be terminated so that the screen cannot fray. If the screen is to be connected then make it off in the same way as for coaxial cable with a soldered pigtail and a sleeve.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 16th 2018, 15:24:21 PM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Linda Cerise. Engine Wiring. Published at Tuesday, January 16th 2018, 09:54:39 AM. Digital Multi-Meters come in two common varieties: Auto- Ranging, and Non Auto-Ranging. A non auto-ranging meter requires you to select a range of “sensitivity” for the given function you are using. For example if you want to measure resistance, you would need to select a range of up to 200 ohms, up to 20Kohms (20,000 ohms), 200Kohms, etc. An auto-ranging meter will automatically figure out the range and give you a measurement.
By Severin Theodore. Engine Wiring. Published at Tuesday, January 16th 2018, 08:59:14 AM. When your ignition switch is in the “run” position your accessory terminal is energized by the battery. Power then runs from the “A” or accessory terminal to a STSP (Single Throw Single Position) switch. This switch is wired in-series and is a way to connect and disconnect power to your accessory such as your headlights. Your headlights are then wired to the STSP light switch and are wired in parallel to each other. This means two wires will come from your light switch and connect to each headlight individually. Two ground wires will also come off each headlight individually and connect to the common ground. If you were to wire your headlights in series each headlight will only use 6 volts rather than 12 and the brightness will be diminished.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 07:21:08 AM. Modern electrical machine tool equipment may vary from that of a single-motor machine (such as a drill press that performs simple, repetitive operations) to very large, multimotored automatic machines, which contain highly complex electrical control systems. Typically, these machines are especially designed, factory-wired, tested by the builder and then erected in the plant.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.