By Claudie Ulysse. Electrical Wiring. Publised at Wednesday, January 24th 2018, 06:23:28 AM. Two or more conductors may only be connected to a terminal that is designed for the purpose. The majority of connecting blocks will only take one or two conductors. Don’t force in any more.
By Annette Noele. Electrical Wiring. Publised at Sunday, January 28th 2018, 18:50:48 PM. Conductors and cables should run from terminal to terminal without any intervening joins. This refers to making a joint in the middle of a wire or cable. If it is necessary for any reason then use a suitable connector or terminal block. Don’t use a twisted and soldered joint.
By Severin Theodore. Electrical Wiring. Publised at Thursday, January 25th 2018, 10:12:47 AM. A conductor is a material which will allow an electric current to flow easily. In the case of a wire connection, it needs to be a very good conductor. Good conductors include most metals. The most common conductor used in wire is copper, although you may come across others such as aluminium. An insulator on the other hand is a material which does not allow an electric current to flow. Rubber and most plastics are insulators.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 21st 2017, 11:04:15 AM. So your tractor lost spark. You purchased a new ignition coil. After you installed it you still don’t have spark. What happened? We will go into this common problem later in the article, but for now remember never make assumptions. Always look for evidence that suggests a cause. Evidence comes in many forms such as smoke coming from your engine, metal particles in your oil, and oil leaks from your transmission.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, September 19th 2017, 10:22:23 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Linda Cerise. Electrical Wiring. Published at Sunday, September 17th 2017, 09:47:57 AM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Claudie Ulysse. Engine Wiring. Published at Sunday, September 17th 2017, 09:47:23 AM. To measure voltage on a battery for example you first turn your meter to DC Voltage. Place the red probe on the positive terminal of the battery and place the black probe on the negative side of the battery or on a common ground. Your voltage will display on the screen.
By Annette Noele. Electrical Wiring. Published at Friday, September 15th 2017, 09:06:53 AM. After successful completion, the troubleshooter can improve their understanding of DC, AC, three phase circuits, Relays, Contactors, PLC, Electronics, and other related technology.
By Charline Rodrigue. Electrical Wiring. Published at Wednesday, September 13th 2017, 08:59:20 AM. You must totally enclose conductors and their connection external to the control panel enclosure in suitable raceways or enclosures. Unless used for flexible connections involving small or infrequent movements, or connections to normally stationary motors, limit switches and other externally mounted devices, fittings used with raceways or multiconductor cables must be liquidtight.
By Charline Rodrigue. Electrical Wiring. Published at Monday, September 11th 2017, 08:48:16 AM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.