By Severin Theodore. Electrical Wiring. Publised at Friday, November 24th 2017, 18:38:11 PM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Linda Cerise. Electrical Wiring. Published at Thursday, October 05th 2017, 13:46:47 PM. Line diagrams, also called “schematic” or “elementary” diagrams, show the circuits which form the basic operation of the controller. They do not indicate the physical relationships of the various components in the controller. They are an ideal means for troubleshooting a circuit.
By Charline Rodrigue. Engine Wiring. Published at Tuesday, October 03rd 2017, 12:11:56 PM. Measuring resistance can indicate the health of a component. For example we can determine if an ignition coil is healthy or not by measuring the resistance of its windings. To measure resistance, set your meter to Ω ohms resistance. If you need to select a range, select the smallest range normally 200 ohms. Place the red probe onto one of the small terminals of the ignition coil, and the black one on the remaining small terminal. Your resistance will then display. A normal ignition coil should read about 3.5 to 4 ohms. If your meter reads a much higher resistance it means your ignition coil may have a short and is faulty.
By Severin Theodore. Electrical Wiring. Published at Sunday, October 01st 2017, 11:35:11 AM. The terminations of shielded or screened conductors should be terminated so that the screen cannot fray. If the screen is to be connected then make it off in the same way as for coaxial cable with a soldered pigtail and a sleeve.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 28th 2017, 11:08:59 AM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
By Severin Theodore. Electrical Wiring. Published at Monday, September 25th 2017, 11:07:46 AM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 21st 2017, 11:04:15 AM. Your ignition switch is a rotary switch that when turned to one of its 3 positions connects and disconnects certain contact terminals located on its backside. In the “start” position, it connects the Battery, Ignition, Rectifier, Accessory, and Start Terminals.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, September 19th 2017, 10:22:23 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.