By Severin Theodore. Electrical Wiring. Publised at Friday, November 24th 2017, 18:38:11 PM. In general, contactors should be kept away from electronic devices. A highly disturbing device (variable speed drive, frequency converter, etc.) will have less radiation in the panel if it is “encapsulated” in a small, electromagnetically sealed, unpainted metal enclosure.
By Severin Theodore. Electrical Wiring. Published at Tuesday, January 16th 2018, 02:14:35 AM. After successful completion, the troubleshooter can improve their understanding of DC, AC, three phase circuits, Relays, Contactors, PLC, Electronics, and other related technology.
By Augustine Yvonne. Engine Wiring. Published at Monday, January 15th 2018, 22:58:26 PM. A great feature of many DMM’s is the continuity setting. The continuity function measures resistance, and if there is a complete connection the meter will give an audible beep. If there is no continuity your DMM will show “OL” on the display meaning there is an open line. You can use this to test for electrical shorts in wiring or components. I commonly use this function to quickly test for shorted ignition switches and ignition coils.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, January 15th 2018, 17:39:06 PM. It would then be connected to the contactors and overload relays that constitute the motor starter. Two of the phases are also connected to the transformer to power the logic. The start and stop buttons are at the left of the box (note: normally these are mounted elsewhere, and a separate layout drawing would be needed).
By Charline Rodrigue. Electrical Wiring. Published at Monday, January 15th 2018, 16:20:30 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Babette Benjamine. Engine Wiring. Published at Tuesday, January 09th 2018, 20:54:52 PM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
By Severin Theodore. Engine Wiring. Published at Sunday, January 07th 2018, 18:37:08 PM. When checking these subsystems keep an eye out for evidence suggesting trouble such as sludge or debris in fuel, missing or damaged air cleaner, score marks on top of piston and cylinder walls, and excessive carbon build up on the intake and exhaust valves. All of these give you valuable insight to your problem.
By Blandine Honorine. Engine Wiring. Published at Friday, January 05th 2018, 10:47:51 AM. Measuring resistance can indicate the health of a component. For example we can determine if an ignition coil is healthy or not by measuring the resistance of its windings. To measure resistance, set your meter to Ω ohms resistance. If you need to select a range, select the smallest range normally 200 ohms. Place the red probe onto one of the small terminals of the ignition coil, and the black one on the remaining small terminal. Your resistance will then display. A normal ignition coil should read about 3.5 to 4 ohms. If your meter reads a much higher resistance it means your ignition coil may have a short and is faulty.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.