By Augustine Yvonne. Electrical Wiring. Publised at Sunday, August 20th 2017, 01:27:26 AM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, January 23rd 2018, 16:06:25 PM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, January 23rd 2018, 14:12:24 PM. A lamp inside an enclosure provided for use during maintenance is an example of such a circuit. The control panel may be isolated but the lamp will require power so that the engineer can see while working on it.
By Babette Benjamine. Electrical Wiring. Published at Tuesday, January 23rd 2018, 13:47:53 PM. A receptacle outlet is one in which one or more receptacles are installed for the purpose of attaching “plug and cord-connected” type devices, and a lighting outlet is one intended for a direct-wired connection to a lamp holder, luminaire (lighting fixture) or ceiling fan.
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, January 23rd 2018, 12:04:25 PM. Dashed lines are drawn between the symbols to denote which switches control specific lights or receptacles. There are quite a few symbols used to represent the devices used in home electrical wiring but some of them are very similar, so care should be used when working with them!
By Claudie Ulysse. Engine Wiring. Published at Tuesday, January 23rd 2018, 09:40:54 AM. When your ignition switch is turned in the “start” and “run” position, the “I” or ignition terminal is energized and power flows from the battery through the primary winding of the ignition coil through the points and back to the engine ground. The primary winding of the ignition coil are the two small terminals marked + (positive) and – (negative). A small gauge wire goes from the ignition switch and connects to the + positive terminal of the ignition coil. The breaker points and condenser are both connected to the – (negative) terminal of the ignition coil. Your spark plug cable is connected to the secondary terminal which is the large wire port in the top of the ignition coil. Your spark plug is then connected to the high tension spark plug cable and screwed into your engine’s combustion chamber.
By Sylviane Marcelline. Engine Wiring. Published at Tuesday, January 23rd 2018, 09:10:46 AM. You can determine the amount of current being used and charged on your tractor’s system by placing the meter in-series with the circuits of the tractor. To do this: first remove your red probe and plug it into the 10 amp Max port on your DMM. Then set your DMM to DC Current with the range of 10 amps. Now you unplug the wire going to your ignition switch’s “B” terminal. By clipping alligator clips to your DMM probes you can now connect one probe to the “B” terminal of your ignition switch, and your other DMM probe to the wire that normally goes to “B” terminal on the ignition switch. Now when you run your tractor the current will flow through the meter and your DMM can give you a reading. It will tell you how many amps are flowing through your system.
By Annette Noele. Electrical Wiring. Published at Tuesday, January 23rd 2018, 08:33:10 AM. Every type of machine has unique requirements when it comes to operator safety. From an electrical standpoint, industrial machine equipment and tools - from drill presses to multi-motored automatic machines.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.