By Annette Noele. Electrical Wiring. Publised at Sunday, February 11th 2018, 07:33:20 AM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Babette Benjamine. Electrical Wiring. Publised at Friday, February 02nd 2018, 06:55:41 AM. For grounded control circuits, you may use a green (with or without one or more yellow stripes) or a bare conductor to connect the transformer terminal to a grounding terminal on the control panel.
By Linda Cerise. Electrical Wiring. Publised at Thursday, February 01st 2018, 20:21:09 PM. After successful completion, the troubleshooter can improve their understanding of DC, AC, three phase circuits, Relays, Contactors, PLC, Electronics, and other related technology.
By Annette Noele. Engine Wiring. Published at Tuesday, January 16th 2018, 20:20:08 PM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
By Blandine Honorine. Engine Wiring. Published at Tuesday, January 16th 2018, 20:05:08 PM. The valve seat is the part of your engine block that makes contact with the valve face on the valve. It needs to be cut with a valve seat cutter. A valve seat cutter is also an expensive tool but not as expensive as a valve grinder.
By Annette Noele. Electrical Wiring. Published at Tuesday, January 16th 2018, 19:03:51 PM. Dashed lines are drawn between the symbols to denote which switches control specific lights or receptacles. There are quite a few symbols used to represent the devices used in home electrical wiring but some of them are very similar, so care should be used when working with them!
By Claudie Ulysse. Engine Wiring. Published at Tuesday, January 16th 2018, 17:12:27 PM. To turn your starter, electricity flows from the battery, through the ignition switch, and to the small terminals on the starter solenoid. This electricity causes an electromagnet inside the starter solenoid to connect the two heavy gauge wires and form a complete circuit. High amperage electric flow then goes through your starter, turning your engine’s flywheel.
By Babette Benjamine. Electrical Wiring. Published at Tuesday, January 16th 2018, 16:16:38 PM. Both line and wiring diagrams are a language of pictures. It is not difficult to learn the basic symbols. Once you do, you are able to read diagrams quickly, and can often understand a circuit at a glance. The more you work with both line and wiring diagrams, the better you will become in analyzing them.
By Augustine Yvonne. Electrical Wiring. Published at Tuesday, January 16th 2018, 15:24:21 PM. Electricity is supplied to your home through your electric utility’s overhead or buried power lines. Before entering your home, electricity passes through a watt-hour meter which measures the amount of electricity used.
By Linda Cerise. Engine Wiring. Published at Tuesday, January 16th 2018, 09:54:39 AM. To measure voltage on a battery for example you first turn your meter to DC Voltage. Place the red probe on the positive terminal of the battery and place the black probe on the negative side of the battery or on a common ground. Your voltage will display on the screen.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.