By Claudie Ulysse. Electrical Wiring. Publised at Tuesday, January 30th 2018, 07:53:29 AM. Connections should be secured against accidental loosening. Correctly tighten terminal screws and where a connecting plug is fitted, use the clamps or screws provided to secure it to its mating socket.
By Annette Noele. Electrical Wiring. Publised at Sunday, January 28th 2018, 19:28:59 PM. For grounded control circuits, you may use a green (with or without one or more yellow stripes) or a bare conductor to connect the transformer terminal to a grounding terminal on the control panel.
By Annette Noele. Electrical Wiring. Publised at Thursday, February 01st 2018, 07:32:39 AM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 21st 2017, 11:04:15 AM. In our example below the bad spark plug ignition cable has a resistance reading of 5 mega ohms. That's 5,000,000 ohms! We know that a typical small engine ignition coil uses between 3 to 5 amps. By using the above mathematical formula we can determine that the bad spark plug ignition cable caused between 15,000,000 to 20,000,000 volts to be generated by the ignition coil!
By Claudie Ulysse. Electrical Wiring. Published at Tuesday, September 19th 2017, 10:22:23 AM. After successful completion, the troubleshooter can improve their understanding of DC, AC, three phase circuits, Relays, Contactors, PLC, Electronics, and other related technology.
By Linda Cerise. Electrical Wiring. Published at Sunday, September 17th 2017, 09:47:57 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Claudie Ulysse. Engine Wiring. Published at Sunday, September 17th 2017, 09:47:23 AM. You can determine the amount of current being used and charged on your tractor’s system by placing the meter in-series with the circuits of the tractor. To do this: first remove your red probe and plug it into the 10 amp Max port on your DMM. Then set your DMM to DC Current with the range of 10 amps. Now you unplug the wire going to your ignition switch’s “B” terminal. By clipping alligator clips to your DMM probes you can now connect one probe to the “B” terminal of your ignition switch, and your other DMM probe to the wire that normally goes to “B” terminal on the ignition switch. Now when you run your tractor the current will flow through the meter and your DMM can give you a reading. It will tell you how many amps are flowing through your system.
By Annette Noele. Electrical Wiring. Published at Friday, September 15th 2017, 09:06:53 AM. When constructing junction boxes and pull boxes, you must be careful to exclude materials such as dust, flyings, oil and coolant. After you complete all wiring operations, you must seal all unused knockouts or openings.
By Charline Rodrigue. Electrical Wiring. Published at Wednesday, September 13th 2017, 08:59:20 AM. Electrical symbols are used on home electrical wiring plans in order to show the location, control point(s), and type of electrical devices required at those locations. These symbols, which are drawn on top of the floor plan, show lighting outlets, receptacle outlets, special purpose outlets, fan outlets and switches.
By Charline Rodrigue. Electrical Wiring. Published at Monday, September 11th 2017, 08:48:16 AM. Electricity is supplied to your home through your electric utility’s overhead or buried power lines. Before entering your home, electricity passes through a watt-hour meter which measures the amount of electricity used.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.