By Annette Noele. Electrical Wiring. Publised at Saturday, September 09th 2017, 08:05:01 AM. • Black represents ungrounded line, load and control conductors at line voltage. • Red represents ungrounded AC control conductors, at less than line voltage. • Blue represents ungrounded DC control conductors. • Yellow represents ungrounded control circuit conductors that may remain energized when the main disconnecting means is in the OFF position. These conductors must be yellow throughout the entire circuit, including wiring in the control panel and the external field wiring. • White or natural gray represents a grounded circuit conductor. • White with blue stripe represents a grounded DC current-carrying circuit conductor. International and European standards require you to use light blue for the neutral conductor. • White with yellow stripe represents grounded AC current-carrying control circuit conductors that remain energized when the disconnecting means is in the OFF position. For additional circuits powered from different sources that remain energized when the main disconnecting means is in the OFF position, you must use striping colors other than green, yellow or blue to uniquely identify the grounded conductors.
By Blandine Honorine. Engine Wiring. Published at Sunday, December 24th 2017, 02:56:15 AM. To solve the leak into the atmospheric vent make sure your float level is adjusted perfectly. The float should be perfectly parallel to the upper carburetor body or sit slightly lower than level. This keeps fuel below where the two halves of the atmospheric vent meet. Also make sure your carburetor halves are not warped when the bolts are tightened down. If there is a visible gap between the two halves of the carburetor at the atmospheric vent; sand down the two halves until the gap is gone.
By Blandine Honorine. Electrical Wiring. Published at Wednesday, December 20th 2017, 00:42:29 AM. Modern electrical machine tool equipment may vary from that of a single-motor machine (such as a drill press that performs simple, repetitive operations) to very large, multimotored automatic machines, which contain highly complex electrical control systems. Typically, these machines are especially designed, factory-wired, tested by the builder and then erected in the plant.
By Severin Theodore. Electrical Wiring. Published at Tuesday, December 19th 2017, 23:13:04 PM. Where the circuits work at different voltages, the conductors must be separated by suitable barriers or all the wires insulated for the highest voltage to which any conductor may be subjected.
By Severin Theodore. Electrical Wiring. Published at Thursday, December 14th 2017, 23:08:15 PM. When the current is switched on or off, the electro-magnetic field increases and decreases, rapidly causing, in effect, a radio signal. The effect is similar to the crackle that can sometimes be heard on the radio or television when something like a fridge switches on and off. This radiated signal can be picked up by the other wires in the system and cause interference to the normal working voltages in the system
By Charline Rodrigue. Electrical Wiring. Published at Sunday, December 10th 2017, 22:32:01 PM. Both line and wiring diagrams are a language of pictures. It is not difficult to learn the basic symbols. Once you do, you are able to read diagrams quickly, and can often understand a circuit at a glance. The more you work with both line and wiring diagrams, the better you will become in analyzing them.
By Annette Noele. Engine Wiring. Published at Friday, December 08th 2017, 20:38:46 PM. A circuit is a closed loop of wiring and components beginning at the positive side of the battery and ending back at the negative side of the battery. This loop is often closed using a common ground. Electricity only flows when a circuit is a closed loop. If the loop is open no electricity flows.
By Annette Noele. Electrical Wiring. Published at Wednesday, December 06th 2017, 19:02:08 PM. The terminations of shielded or screened conductors should be terminated so that the screen cannot fray. If the screen is to be connected then make it off in the same way as for coaxial cable with a soldered pigtail and a sleeve.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.