By Charline Rodrigue. Electrical Wiring. Publised at Tuesday, January 23rd 2018, 04:58:13 AM. A receptacle outlet is one in which one or more receptacles are installed for the purpose of attaching “plug and cord-connected” type devices, and a lighting outlet is one intended for a direct-wired connection to a lamp holder, luminaire (lighting fixture) or ceiling fan.
By Annette Noele. Electrical Wiring. Publised at Tuesday, January 23rd 2018, 16:54:52 PM. This section requires you to support conductors in panels to keep them in place. You're permitted to use wiring channels if they're made of a flame-retardant insulating material. If you're working with back-connected control panels, you must provide access doors or swing out panels that swing about a vertical axis. Multiple-device control panels must have terminal blocks or attachment plugs and receptacles to terminate and connect all outgoing control conductors.
By Blandine Honorine. Engine Wiring. Published at Sunday, November 05th 2017, 17:03:19 PM. Measuring resistance can indicate the health of a component. For example we can determine if an ignition coil is healthy or not by measuring the resistance of its windings. To measure resistance, set your meter to Ω ohms resistance. If you need to select a range, select the smallest range normally 200 ohms. Place the red probe onto one of the small terminals of the ignition coil, and the black one on the remaining small terminal. Your resistance will then display. A normal ignition coil should read about 3.5 to 4 ohms. If your meter reads a much higher resistance it means your ignition coil may have a short and is faulty.
By Linda Cerise. Engine Wiring. Published at Sunday, October 22nd 2017, 15:27:26 PM. To measure voltage on a battery for example you first turn your meter to DC Voltage. Place the red probe on the positive terminal of the battery and place the black probe on the negative side of the battery or on a common ground. Your voltage will display on the screen.
By Augustine Yvonne. Electrical Wiring. Published at Wednesday, October 18th 2017, 14:48:20 PM. Ensure that identification tags and cable markers are legible, marked with a permanent ink and suitable for the environment where the panel is to be used. They should also correspond with those shown in the machine drawings and instruction or service documentation.
By Claudie Ulysse. Engine Wiring. Published at Saturday, October 14th 2017, 14:15:58 PM. Insert the valve cutter pilot into the valve guide, and gently place the appropriate valve cutter into the pilot. Using the “T” handle apply gentle finger pressure downwards while rotating the tool. This is all it takes to cut into the valve seats. Do this for a few revolutions. Finish, by turning the “T” handle a few times without applying finger pressure. When done correctly you should see that you have cut a uniform area around your valve seat. Repeat this process with your other valve seat.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, October 09th 2017, 14:02:09 PM. Wiring diagrams show the connections to the controller. Wiring diagrams, sometimes called “main” or “construction” diagrams, show the actual connection points for the wires to the components and terminals of the controller.
By Linda Cerise. Electrical Wiring. Published at Thursday, October 05th 2017, 13:46:47 PM. You are required to use pressure connectors to connect conductors to devices with lug-type terminals that are not equipped with saddle straps or equivalent means of retaining conductor strands.
By Charline Rodrigue. Engine Wiring. Published at Tuesday, October 03rd 2017, 12:11:56 PM. Let’s say you attempt to start your tractor and your starter does not engage. No click of the solenoid, nothing happens at all. Before assuming your starter is bad, grab your DMM and set it to DC Volts. Remove the wire going to the small terminal of your starter solenoid and connect the red probe of your DMM to the wire. Now connect your black probe to a ground. Turn your tractor’s key. Your DMM reads no voltage. This tells you that power is not going from your battery to the solenoid. Next remove the wires from the back of your ignition switch that are connected to the “B” and “S” terminals on your switch. Set your DMM to Continuity and connect your probes to the “B” and “S” terminals of the switch. Turn your tractor’s key and if there is no “beep” you know your ignition switch has a short internally and should be replaced.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.