By Augustine Yvonne. Electrical Wiring. Publised at Wednesday, August 30th 2017, 02:31:22 AM. For grounded control circuits, you may use a green (with or without one or more yellow stripes) or a bare conductor to connect the transformer terminal to a grounding terminal on the control panel.
By Sylviane Marcelline. Electrical Wiring. Published at Monday, October 09th 2017, 14:02:09 PM. Every type of machine has unique requirements when it comes to operator safety. From an electrical standpoint, industrial machine equipment and tools - from drill presses to multi-motored automatic machines - can present special fire and shock hazards.
By Linda Cerise. Electrical Wiring. Published at Thursday, October 05th 2017, 13:46:47 PM. This section requires you to support conductors in panels to keep them in place. You're permitted to use wiring channels if they're made of a flame-retardant insulating material. If you're working with back-connected control panels, you must provide access doors or swing out panels that swing about a vertical axis. Multiple-device control panels must have terminal blocks or attachment plugs and receptacles to terminate and connect all outgoing control conductors.
By Charline Rodrigue. Engine Wiring. Published at Tuesday, October 03rd 2017, 12:11:56 PM. In our example below the bad spark plug ignition cable has a resistance reading of 5 mega ohms. That's 5,000,000 ohms! We know that a typical small engine ignition coil uses between 3 to 5 amps. By using the above mathematical formula we can determine that the bad spark plug ignition cable caused between 15,000,000 to 20,000,000 volts to be generated by the ignition coil!
By Severin Theodore. Electrical Wiring. Published at Sunday, October 01st 2017, 11:35:11 AM. Electrical equipment uses a wide variety of wire and cable types and it is up to us to be able to correctly identify and use the wires which have been specified. The wrong wire types will cause operational problems and could render the unit unsafe.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 28th 2017, 11:08:59 AM. When your ignition switch is turned in the “start” and “run” position, the “I” or ignition terminal is energized and power flows from the battery through the primary winding of the ignition coil through the points and back to the engine ground. The primary winding of the ignition coil are the two small terminals marked + (positive) and – (negative). A small gauge wire goes from the ignition switch and connects to the + positive terminal of the ignition coil. The breaker points and condenser are both connected to the – (negative) terminal of the ignition coil. Your spark plug cable is connected to the secondary terminal which is the large wire port in the top of the ignition coil. Your spark plug is then connected to the high tension spark plug cable and screwed into your engine’s combustion chamber.
By Severin Theodore. Electrical Wiring. Published at Monday, September 25th 2017, 11:07:46 AM. It is uncommon for engineers to build their own PLC panel designs (but not impossible of course). For example, once the electrical designs are complete, they must be built by an electrician. Therefore, it is your responsibility to effectively communicate your design intentions to the electricians through drawings.
By Augustine Yvonne. Engine Wiring. Published at Thursday, September 21st 2017, 11:04:15 AM. First apply some of the lapping compound to the valve face area with your finger. It only requires a small amount of compound. Gently place your valve into the engine. Use the Lapping stick by pushing the suction cup into the top of the valve and rotate it back and forth in between your hands. After about 10 seconds remove the valve and wipe the lapping compound off of both the valve and the valve seat. Inspect and make sure the contact area is uniform and about in the middle of the valve face. Repeat this process with the other valve and seat.
D-42 - Engine Wiring Diagram Specialist
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.